Southbend SB1231 Bedienungsanleitung PDF herunterladen

Chucks are heavy! Get assistance when

installing or removing the chuck from the

lathe. Wear heavy duty leather boots for

foot and toe protection, and keep hands and

fingers away from all pinch points. Ignoring

this warning can lead to a severe crushing

injury or finger amputation!

Speciﬁcations

• OD Clamping ...... 0.69"–10.04" (17.5–255mm)

• ID Clamping .......... 3.74"–10.83" (95–275mm)

• Chuck Bore Diameter ................2.56" (65mm)

• Chuck Outer Diameter ..........11.81" (300mm)

• Maximum Speed ...........................2500 RPM*

• Mounting Type ......................... D1-8 Camlock

• Construction ..................Fine-GrainCast-Iron

• ChuckWeight ......................................... 80lbs

• ChuckShippingWeight ......................... 85lbs

• Country of Origin ................................ Taiwan

* ThemaximumspeedlistedaboveisONLY

possiblewiththechuckjawsandthe

workpieceincompleterotationalsymmetry.

Theworkpieceweightmustbewithinthe

limitsofthelathe,andtheworkpiecemass

mustbeofequaldensitythroughoutto

preventcentrifugalimbalanceorradial

runout—evenifatailstockorothersupport

isusedforadditionalsupport.

Instruction Sheet

PHONE: (360) 734-1540 • www.southbendlathe.com

MODEL SB1231

12" 4-JAW INDEPENDENT CHUCK

WARNING: No portion of this manual may be reproduced without written approval.

#CR13310 Printed in Taiwan

Figure 1. Features.

Introduction

TheModelSB1231usesadirectmountD1-8

camlocksystemwherethecamlockstudsare

directlythreadedintotothechuckbodyinstead

of being threaded into a backing plate that

isboltedtothechuck.Withoutusingaback

platetomountthechuck,thechuckjawsare

positionedclosertotheheadstockwhichgives

alongerdistancebetweenthejawsandthe

tailstock.Anotherbenefitisthatthedistance

betweenthejawsandtheoutboardspindlenose

isreduced,soifaspidersupportisusedonthe

outboardspindle,shortgunbarrelsandother

shorterworkpiecescanbeheldatbothends.

Manufactured

with high-tech

German CNC

machinery

Fine-grain cast

iron body

Hardened steel jaws

for durability and

extreme clamping

force and grip

Independent jaw

screws for each

reversible jaw

Direct

camlock

spindle

mounting

Jaw screw

retaining pin

with lock screws

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - MODEL SB1231

Chucks are heavy! Get assistance when installing or removing the chuck from the lathe. Wear heavy duty leather boots for foot and toe protection, and

Seite 2 - INSTRUCTIONS

Safety• Chuck Key Safety:Achuckkeyleftinthechuckcanbecomeadangerousprojectilewhenthespindleisstarted.Alwaysremovethechuckkeya

Seite 3 - Camlock Stud Adjustment

Camlock Stud InstallationThecamlockstudsthatareshippedwiththischuckmaybepre-installedfromthefactory.Ifsoskipthissectionandcomplet

Seite 4

6. Withthehelpofanotherperson,orwiththehelpofachuckcradle,alignthechuckwiththespindlesothestudsandcamlockboresarealignedc

Seite 5

7.  Tightencamlocksinastarpatterntodrawthechuckinevenlyandreducethechanceofmisalignment.Makesuretotightencamlocksinanincreme

Seite 6 - Operation

CAUTION: During the next step, the chuck may come off suddenly, so it is important that you are ready to support its weight with a chuck cradle to p

Seite 7 - Care & Maintenance

Jaw screw retaining pinSet screwaFigure 10. Chuck sequence of disassembly.Care & MaintenanceAlways disconnect machine from power before performin

Seite 8 - Parts Diagram

TroubleshootingSymptom Possible Cause Possible SolutionThechuckhashardspotsorbindscompletely.1.Jawisinapoorpositionforclamping.1.Re-inst

Kommentare zu diesen Handbüchern

Keine Kommentare

Southbend SB1231 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Drehmaschinen Southbend SB1231 herunter. Southbend SB1231 User's Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Drehmaschinen Southbend SB1231